Wolfvision EYE-12 User Manual Manual de usuario descargar pdf (Pagina 12)

+ 12V

GND

When a locked power connector and/or other power supply is necessary, the

supplied power connector can be used.

The power supply is optional if Power over Ethernet (PoE) is used (see page 12).

The power source equipment shall comply with all applicable local and

national codes related to safety.

Power Plug

DVI-I Port

1 - T.M.D.S. Data2- 9 - T.M.D.S. Data1- 17 - T.M.D.S. Data0-

2 - T.M.D.S. Data2+ 10 - T.M.D.S. Data1+ 18 - T.M.D.S. Data0+

3 - T.M.D.S. Data2/4 Shield 11 - T.M.D.S. Data1/3 Shield 18 - T.M.D.S. Data0+

4 - T.M.D.S. Data4- (*) 12 - T.M.D.S. Data3- (*) 19 - T.M.D.S. Data0/5 Shield

5 - T.M.D.S. Data4+(*) 13 - T.M.D.S. Data3+ (*) 20 - T.M.D.S. Data5- (*)

6 - DDC Clock 14 - +5V Power 21 - T.M.D.S. Data5+ (*)

7 - DDC Data 15 - Ground (return for +5V, 22 - T.M.D.S. Clock+

8 - Analog Vertical Sync HSync and Vsync) 23 - T.M.D.S. Clock-

C1 - Analog Red 16 - Hot Plug Detect 24 - Analog Vertical Sync

C4 - Analog Horizontal Sync C2 - Analog Green C3 - Analog Blue

C5 - Analog Ground *...not used

(analog R, G & B return)

Pin 24

Pin 8

Pin 1

Pin 9

Pin 17

The DVI-I port (#13) provides digital and analog signals.

For using HDMI, a DVI-HDMI cable or adapter is required.

In some rooms, the built-in IR-receiver may . In this case connect the supplied external

receiver to the IR-SENSOR plug (#12) and position the IR-sensor somewhere on the ceiling (or in

the room)

not be enough

infrared

where the users normally point the remote control at.

External Infrared (IR) Sensor

RS-232, Serial Control Input

9-pin D-Sub connector

on unit; male

(front side)

The serial port (#10) can be used to control the EYE-12 through an external device, such as a room control

system.

Pins: 2: RX, 3: TX, 5: GND

Baud Rate: 9200, 19200, 38400, 57600 or 115200 (selectable)

databits: 8, stopbit: 1, parity: no

The baud rate can be changed in the on-screen extra menu by keeping

pressed the menu key until it appears (see page 10).

RGB Port

1 - Analog Red video 6 - Red return 11 - N/C Not connected

2 - Analog Green video 7 - Green return 12 - SDA I²C data

3 - Analog Blue video 8 - Blue return 13 - HSync Horizontal sync

4 - N/C Not connected 9 - SENSE +5 V DC from Visualizer 14 - VSync Vertical sync

5 - GND Ground 10 - GND Ground (VSync, DDC) 15 - SCL I²C clock

15-pin D-Sub HD

connector female

(front side, unit)

The RGB port (#11) provides analog RGBHV signal.

IMPORTANT

DVI-I connector female

(front side, unit)

The complete protocol can be found on our internet website under: www.wolfvision.com/support

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 43 44

Comentarios a estos manuales

Sin comentarios

Wolfvision EYE-12 User Manual Manual de usuario Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para Videocámaras Wolfvision EYE-12 User Manual