Wolfvision VZ-57plus User Manual Manual de usuario descargar pdf (Pagina 14)

SERIAL PORT / SERIAL PROTOCOL

9-pin D-Sub connector

on unit, male, front side

Pins: 2: RX, 3: TX, 5: GND, 7: RTS, 8: CTS

Baud rate: 9200, 19200, 38400, 57600 or 115200 (selectable)

databits: 8, stopbit: 1, parity: no

Please note: DecimaI-Codes (=ASCII-Codes or Hex-Codes) must be sent as one

single byte (e.g. 199 and not: 1 + 1 + 9) !

The serial port can be used to control the Visualizer through an external device, like a remote control

system for a complete conference room.

A detailed description of the serial protocol (including status report and position setting) can be

downloaded from our website: http://www.wolfvision.com/support.

DVI PORT

Pin 24

Pin 8

Pin 1

Pin 9

Pin 17

1 - T.M.D.S. Data2- 9 - T.M.D.S. Data1- 17 - T.M.D.S. Data0-

2 - T.M.D.S. Data2+ 10 - T.M.D.S. Data1+ 18 - T.M.D.S. Data0+

3 - T.M.D.S. Data2/4 Shield 11 - T.M.D.S. Data1/3 Shield 18 - T.M.D.S. Data0+

4 - T.M.D.S. Data4- (*) 12 - T.M.D.S. Data3- (*) 19 - T.M.D.S. Data0/5 Shield

5 - T.M.D.S. Data4+(*) 13 - T.M.D.S. Data3+ (*) 20 - T.M.D.S. Data5- (*)

6 - DDC Clock 14 - +5V Power 21 - T.M.D.S. Data5+ (*)

7 - DDC Data 15 - Ground (return for +5V, 22 - T.M.D.S. Clock+

8 - Analog Vertical Sync HSync and Vsync) 23 - T.M.D.S. Clock-

C1 - Analog Red 16 - Hot Plug Detect 24 - Analog Vertical Sync

C4 - Analog Horizontal Sync C2 - Analog Green C3 - Analog Blue

C - Analog Ground

(analog R, G & B return) *...not used

Before changing a fuse disconnect the power cable. The fuse (#34)

is situated behind a small lid above the power socket and the main

power switch. It can easily be opened with a small screwdriver etc..

Please put the new fuse(s) carefully into the socket, and put the socket

the right way round into the socket holder.

The type of fuse is: T 3,15A. Do not use any other type !

Change the fuse for a new one and switch the unit on. If the fuse fails

again contact your WolfVision Visualizer dealer!

EXCHANGING A FUSE

IMPORTANT

MIRROR - CLEANING

Mirror: Please note that dust on the base mirror (#2) inside the unit

has little effect on the picture quality (as it is out of the

focal range). However the top mirror (#3) always has to be kept clean!

Wipe the mirror gently with the supplied WolfVision cleaning tissue!

Normal dry cleaning or cleaning together with breathing a bit on the mirror should be sufficient

(If not, use a special optical cleaner only!)

Please note: Switch off the power before cleaning a mirror in order to make sure that the Laser Center

Marker is off.

CAUTION: Sensitive front coated mirror!

Move the tissue in vertical direction only ! (horizontal scratches

would cause ugly reflections) Avoid high pressure !

DO NOT USE ORDINARY GLASS CLEANER OR ALCOHOL

- THE RESULT WOULD BE A SLIGHTLY BLUE MIRROR SURFACE !

The glass covering the mirror inside the unit should also be kept clean.

Cabinet: Clean the cabinet by gently wiping it with a soft cloth.

Never use strong cleaning agents such as benzene or alcohol!

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 35 36

Comentarios a estos manuales

Sin comentarios

Wolfvision VZ-57plus User Manual Manual de usuario Pagina 14

Comentarios a estos manuales

Relacionado con productos y manuales para Videocámaras Wolfvision VZ-57plus User Manual