Wolfvision VZ-C12 User Manual Manual de usuario descargar pdf (Pagina 15)

9-pin D-Sub connector

on unit; male

(front side)

The complete serial protocol can be found on our internet homepage:

www.wolfvision.com/support

The serial port (#19) can be used to control the Visualizer through an external device, such

as a room control system that are used to integrate converence rooms.

Please note that ecim odes (=ASCII odes or Hex odes)

must be sent as one single byte (e.g. 199 and not: 1 + 1 + 9) !

Pins: 2: RX, 3: TX, 5: GND

Baud Rate: 9200, 19200, 38400, 57600 or 115200 (selectable)

databits: 8, stopbit: 1, parity: no

The baud rate can be changed in the on-screen extra menu

(see page 15).

d al c c c

PAL / NTSC Video Outputs VZ-C32 only

RS 232, Serial Control Input

DVI Port

1 - T.M.D.S. Data2- 9 - T.M.D.S. Data1- 17 - T.M.D.S. Data0-

2 - T.M.D.S. Data2+ 10 - T.M.D.S. Data1+ 18 - T.M.D.S. Data0+

3 - T.M.D.S. Data2/4 Shield 11 - T.M.D.S. Data1/3 Shield 18 - T.M.D.S. Data0+

4 - T.M.D.S. Data4- (*) 12 - T.M.D.S. Data3- (*) 19 - T.M.D.S. Data0/5 Shield

5 - T.M.D.S. Data4+(*) 13 - T.M.D.S. Data3+ (*) 20 - T.M.D.S. Data5- (*)

6 - DDC Clock 14 - +5V Power 21 - T.M.D.S. Data5+ (*)

7 - DDC Data 15 - Ground (return for +5V, 22 - T.M.D.S. Clock+

8 - Analog Vertical Sync HSync and Vsync) 23 - T.M.D.S. Clock-

C1 - Analog Red 16 - Hot Plug Detect 24 - Analog Vertical Sync

C4 - Analog Horizontal Sync C2 - Analog Green C3 - Analog Blue

C5 - Analog Ground *...not used

(analog R, G & B return)

Pin 24

Pin 8

Pin 1

Pin 9

Pin 17

The S-video (Y/C) (#21) and Composite (#17) video outputs can be switched between PAL

and NTSC in the units on-screen menu (see page 15).

Please note, that the picture quality of the S-video (#21) output is BETTER than the quality

of the Composite (#17) video output. However the picture quality of both video outputs is BY

FAR NOT AS GOOD as the picture quality of the data outputs (#16, #18, #22 and #23). This

is because of the limitations of the PAL/NTSC video system and because of the fact that

this is just a converted Progressive Scan signal and not an original video signal.

By default, the video output is switched off and can be activated in the on-screen menu

(see page 15).

Lightbox (optional)

When a lightbox is used, the top light of the Visualizer should be switched off

with the LIGHT key (#33).

Using a bottom light has the disadvantage that the Synchronized Lightfield of the top light

no longer marks the pick-up area of the built-in camera.

When switching off the top light, the Ceiling Visualizer also switches the white balance

adjustment from "one-push" white balance to "auto-tracking" white balance. This

compensates the varying color temperatures of different light sources - see page 11.

The recommended lightbox for the Ceiling Visualizer is the WolfVision Lightbox LB-38.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 43 44

Comentarios a estos manuales

Sin comentarios

Wolfvision VZ-C12 User Manual Manual de usuario Pagina 15

Comentarios a estos manuales

Relacionado con productos y manuales para Videocámaras Wolfvision VZ-C12 User Manual